| Page: |
| Home > Help Needed / General Tech Chat > best cam for use with titan 1.5 roller rockers????? | |||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 08:30:24am
Hi I've done a search but can't seem to find this particular question out which cam will be best to use in my new build iam going to be using 1.5 roller rockers & don't know weather to go for a n/a mg cam or an avonbar phase 2 or any other suggestions would be grate intended boost is 15psi many thanks scott |
||||||
 8215 Posts Member #: 90 Post Whore Somewhere around Swindon |
24th Feb, 2011 at 08:42:54am
none bin the rollers imo Crystal Sound Audio said:
Why wolfie...you should have your name as Fuckfaceshithead ! "A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools."-Douglas Adams |
||||||
 7265 Posts Member #: 1268 The Boom Boom speaker Police! Essex |
24th Feb, 2011 at 08:56:49am
The question should be. 'Which ratio rockers suit my cam' In the 13's at last!.. Just |
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 09:00:04am
I've already got the rockers & no cam so can get any cam that will suit really why would you bin the rollers wolfie? What's people using std turbo ones? |
||||||
|
8215 Posts Member #: 90 Post Whore Somewhere around Swindon |
24th Feb, 2011 at 09:09:12am
well the ph2 was not designed for 1.5 rockers and i ran some 1.5's with an mg cam and drivability was horrible, took them off and was much better
Crystal Sound Audio said:
Why wolfie...you should have your name as Fuckfaceshithead ! "A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools."-Douglas Adams |
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 09:21:22am
What is the better cam out the n/a mg & the phase 2? Forgetting the rockers for now? |
||||||
 7765 Posts Member #: 74 I pick holes in everything.. Chief ancient post excavator |
24th Feb, 2011 at 09:26:25am
You don't build an engine around your rockers. You fit 1,5 rockers if these suit the rest of the build. On 13th Jul, 2012 Ben H said:
Mine gets in the way a bit, but only when it is up. If it is down it does not cause a problem. |
||||||
|
8215 Posts Member #: 90 Post Whore Somewhere around Swindon |
24th Feb, 2011 at 09:30:12am
what power you aiming for and is the car a daily driver? Crystal Sound Audio said:
Why wolfie...you should have your name as Fuckfaceshithead ! "A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools."-Douglas Adams |
||||||
 9258 Posts Member #: 123 Post Whore Betwix Harrogate and York |
24th Feb, 2011 at 09:31:47am
As it happens I tried the 1.5s with the PH2 and it was useless. But I use them with the MG cam and it's ace.
Fastest 998 mini in the world? 13.05 1/4 mile 106mph
On 2nd Jan, 2013 fastcarl said:
the design shows a distinct lack of imagination, talk about starting off with a clean sheet of paper, then not bothering to fucking draw on it,lol On 20th Apr, 2012 Paul S said:
I'm mainly concerned about swirl in the runners caused by the tangential entry. |
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 11:20:31am
The cars not a daily driver just weekend & when I fancy a blast iam after about 150bhp keeping std turbo pistons having the head worked cam? Rockers? Intercooler & 15psi |
||||||
 9812 Posts Member #: 332 Resident Cylinder Head Modifier Mitsi Evo 7, 911, Cossie. & all the chavs ...... won no problem |
24th Feb, 2011 at 11:53:48am
go for the phase 2 timed in @ 107 deg and use 1.3 roller rockers, minisport do some decent ones for a good price which have been tried and tested
|
||||||
|
8215 Posts Member #: 90 Post Whore Somewhere around Swindon |
24th Feb, 2011 at 12:31:37pm
i am with steve ph2 with 1.3's Crystal Sound Audio said:
Why wolfie...you should have your name as Fuckfaceshithead ! "A common mistake that people make when trying to design something completely foolproof is to underestimate the ingenuity of complete fools."-Douglas Adams |
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 01:09:23pm
Iam goin to get green & white to do me a straight cut box if I can't find a good 1cheaper are the mini sport rockers tips or full roller? Am I right in thinking std rockers are 1.3 ratio? Could you pm me a contact number please steve (benross) to discuss some prices on building an engine etc |
||||||
 16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
24th Feb, 2011 at 02:02:24pm
standard rockers are 1.2 something On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it 
|
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 02:37:42pm
No bother just wasn't sure |
||||||
|
1394 Posts Member #: 1346 Post Whore bromsgrove |
24th Feb, 2011 at 03:22:04pm
what is your engine spec |
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 04:54:16pm
Well iam planing on std turbo pistons & new rings I had turbo phil mod a head a while back with 26cc chambers its goin to be ported I already have some 1.5roller rockers a ported exhaust manifold & elbow intercooler set up & a cam of some sort but as I had the rockers already wasn't sure what cam to go for or what would work well iam planing on 15psi boost the engine in the car now is std apart from green air filter,exhaust,intercooler & the 26cc head running 12psi made 130 on the rollers at peter burgess on tuesday but as its not a new build & I already have rings was goin to start a fresh build |
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 04:59:06pm
Well iam planing on std turbo pistons & new rings I had turbo phil mod a head a while back with 26cc chambers its goin to be ported I already have some 1.5roller rockers a ported exhaust manifold & elbow intercooler set up & a cam of some sort but as I had the rockers already wasn't sure what cam to go for or what would work well iam planing on 15psi boost the engine in the car now is std apart from green air filter,exhaust,intercooler & the 26cc head running 12psi made 130 on the rollers at peter burgess on tuesday but as its not a new build & I already have rings was goin to start a fresh build |
||||||
|
16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
24th Feb, 2011 at 05:16:58pm
Our metro van has standard turbo pistons, well ported head, n/a mg cam, T3 on a ported manifold. Made 153BHP on about 14-15psi. We're using cooper style pressed rockers. On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it
|
||||||
|
461 Posts Member #: 9229 Senior Member newcastle upon tyne |
24th Feb, 2011 at 05:22:01pm
That sound exactly the kind of thing iam after is the ratio of the rockers 1.5 with them pressed steel ones? |
||||||
|
16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
24th Feb, 2011 at 06:05:42pm
nope, 1.2 something, just a bit more than standard ones. What was available on a limited budget. If funds stretched to it, I would put 1.3 rollers on it. It will be getting a AB phase 2 cam in the near future. On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it
|
||||||
 5417 Posts Member #: 6181 Double hard bastard brookwood woking |
24th Feb, 2011 at 09:07:59pm
On 24th Feb, 2011 BENROSS said:
go for the phase 2 timed in @ 107 deg and use 1.3 roller rockers, minisport do some decent ones for a good price which have been tried and tested every engine is diffrent but ............ thats my thought for a weekend warrior will your diff drops etc clutch stand the extra your going to put through it ? S~~t F~~k S~~T i was told that it would work. I have an avon bar phase 2 and some 1.5 rockers from my N/A 1380. So it looks like i now need a set of 1.3 rockers. Any one what to swap lol simon. I have started posting on Instagram also my name on there is turbomk1golf
On 1st Nov, 2007 Ben H said:
There is no such thing as 'insignificant weight saving', it all adds up. |
||||||
 1648 Posts Member #: 9038 Post Whore Carlisle, Cumbria |
24th Feb, 2011 at 09:16:34pm
its pay day on monday MadMk1 get some then, sure your wage can stretch |
||||||
 1596 Posts Member #: 8027 Post Whore Thrapston, Kettering, Northants NN14 |
24th Feb, 2011 at 09:16:57pm
I'm glad I didn't buy a set now lol. On 17th Feb, 2011 apbellamy said:
I popped my first one out the other day... |
||||||
|
5417 Posts Member #: 6181 Double hard bastard brookwood woking |
24th Feb, 2011 at 09:28:31pm
On 24th Feb, 2011 hazpalmer said:
its pay day on monday MadMk1 get some then, sure your wage can stretch Not with lots of bits still to get, Also its the wifes Bday looks like she is getting a new stack rev Counter then!! I have been looking at the MED rockers is anyone running them. simon. Edited by madmk1 on 24th Feb, 2011. I have started posting on Instagram also my name on there is turbomk1golf
On 1st Nov, 2007 Ben H said:
There is no such thing as 'insignificant weight saving', it all adds up. |
||||||
| Home > Help Needed / General Tech Chat > best cam for use with titan 1.5 roller rockers????? | |||||||
|
|||||||
| Page: |