| Page: |
| Home > Help Needed / General Tech Chat > NoDIZ map?? | |||||||
 330 Posts Member #: 9628 Senior Member |
12th May, 2014 at 05:10:20pm
i have a no diz fitted which im using a map from a R5 turbo, im not going to drive the car will the map be ok just to get it running?
|
||||||
 9502 Posts Member #: 1023 Post Whore Doncaster, South Yorkshire |
12th May, 2014 at 05:42:29pm
Why not put in one of the many maps floating about this forum?
Yes i moved to the darkside |
||||||
 3673 Posts Member #: 9300 Post Whore Quarry Bonk |
12th May, 2014 at 06:03:39pm
I wouldn't have thought a Renault 5 map would be of much use, it's a completely different engine :S On 26th Jan, 2012 Tom Fenton said:
ring problems are down to wear or abuse but although annoying it isn't a show stopper On 5th Aug, 2014 madmk1 said:
Shit the bed! I had snapped the end of my shaft off!! 17.213 @ 71mph, 64bhp n/a (Old Engine) |
||||||
|
330 Posts Member #: 9628 Senior Member |
12th May, 2014 at 06:06:11pm
never used a tuning software so i dont have an idea what to use :L
|
||||||
|
3673 Posts Member #: 9300 Post Whore Quarry Bonk |
12th May, 2014 at 06:08:52pm
Just search TM for a general map for a similar spec of engine build for megajolt and copy the table values in, don't think nodiz would accept a megajolt file, but you could always try it, they may/may not have built compatibility into the software. On 26th Jan, 2012 Tom Fenton said:
ring problems are down to wear or abuse but although annoying it isn't a show stopper On 5th Aug, 2014 madmk1 said:
Shit the bed! I had snapped the end of my shaft off!! 17.213 @ 71mph, 64bhp n/a (Old Engine) |
||||||
|
330 Posts Member #: 9628 Senior Member |
12th May, 2014 at 06:12:36pm
thank you, i just did a search of here for a 998 turbo map but nothing came up :/
|
||||||
|
3673 Posts Member #: 9300 Post Whore Quarry Bonk |
12th May, 2014 at 06:27:12pm
If you ask Wil H nicely he may send you a map, he's the most likely person I can think of at the moment to have one On 26th Jan, 2012 Tom Fenton said:
ring problems are down to wear or abuse but although annoying it isn't a show stopper On 5th Aug, 2014 madmk1 said:
Shit the bed! I had snapped the end of my shaft off!! 17.213 @ 71mph, 64bhp n/a (Old Engine) |
||||||
|
330 Posts Member #: 9628 Senior Member |
12th May, 2014 at 06:37:59pm
awesome thanks mate |
||||||
|
9502 Posts Member #: 1023 Post Whore Doncaster, South Yorkshire |
12th May, 2014 at 08:18:36pm
Whynot email nodiz guys they was on here not long back Yes i moved to the darkside |
||||||
|
330 Posts Member #: 9628 Senior Member |
12th May, 2014 at 08:27:02pm
On 12th May, 2014 Brett said:
Whynot email nodiz guys they was on here not long back he told me to use the R5 map :L |
||||||
 11046 Posts Member #: 965 Post Whore Preston On The Brook |
12th May, 2014 at 08:30:42pm
On 12th May, 2014 coopdog said:
On 12th May, 2014 Brett said:
Whynot email nodiz guys they was on here not long back he told me to use the R5 map :L Sums that up then On 26th Oct, 2004 TurboDave16v said:
Is it A-Series only? I think it should be... So when some joey comes on here about how his 16v turbo vauxhall is great compared to ours, he can be given the 'bird'... On 26th Oct, 2004 Tom Fenton said:
Yep I agree with TD........ |
||||||
|
9502 Posts Member #: 1023 Post Whore Doncaster, South Yorkshire |
12th May, 2014 at 08:53:17pm
On 12th May, 2014 Sprocket said:
On 12th May, 2014 coopdog said:
On 12th May, 2014 Brett said:
Whynot email nodiz guys they was on here not long back he told me to use the R5 map :L Sums that up then ohh dear Yes i moved to the darkside |
||||||
 1745 Posts Member #: 375 Post Whore Leicestershire |
12th May, 2014 at 09:07:28pm
I don't have a map but I did use a R5 GTT map when I first went to my Adaptronic setup. Just be careful as they usually run more advance higher up the rev range. Ron |
||||||
|
330 Posts Member #: 9628 Senior Member |
13th May, 2014 at 09:58:57am
On 12th May, 2014 Star Mag said:
I don't have a map but I did use a R5 GTT map when I first went to my Adaptronic setup. Just be careful as they usually run more advance higher up the rev range. Ron would any turbo map work? just to get it going? |
||||||
 2054 Posts Member #: 452 Post Whore Chester, UK |
13th May, 2014 at 01:35:06pm
there is a mini nodiz map on the nodiz forum. if you load that as a base then just change the numbers around boost area. |
||||||
|
614 Posts Member #: 2153 Post Whore kings langley |
13th May, 2014 at 01:57:58pm
Set the whole map to 10 degrees this allows you to check the timing with a strobe light to see if your trigger is in the correct position. Then run the map off the nodiz site as Taz says Speeding is like masturbating, everyone does it, but not all of us film it and put it on the internet
|
||||||
|
330 Posts Member #: 9628 Senior Member |
13th May, 2014 at 04:02:19pm
ive never done anything with maps or Ecu so i dont know where i would change it? |
||||||
|
614 Posts Member #: 2153 Post Whore kings langley |
13th May, 2014 at 09:29:57pm
Hadn't you better have a play with the software and read the FAQ page work some of this stuff out? At least master the basics of uploading and editing the maps and work out the functions of the ecu before you go any further Speeding is like masturbating, everyone does it, but not all of us film it and put it on the internet
|
||||||
|
330 Posts Member #: 9628 Senior Member |
14th May, 2014 at 11:14:48am
On 13th May, 2014 supermotolee said:
Hadn't you better have a play with the software and read the FAQ page work some of this stuff out? At least master the basics of uploading and editing the maps and work out the functions of the ecu before you go any further thats why im asking for maps to look at them, but the tuning software doesnt allow you to work offline :( |
||||||
|
2054 Posts Member #: 452 Post Whore Chester, UK |
14th May, 2014 at 12:38:48pm
You can still view the map, then copy it to excel etc etc. Not ideal but its a means to an end.
Edited by t@z on 14th May, 2014. |
||||||
|
330 Posts Member #: 9628 Senior Member |
14th May, 2014 at 01:01:22pm
On 14th May, 2014 t@z said:
You can still view the map, then copy it to excel etc etc. Not ideal but its a means to an end. I do recommend you read the manual and try to use what you have around you to work with, not flat out i cant do it. it wont let me load a map at all :L thats the thing. is the map you are using atm? Edited by coopdog on 14th May, 2014. |
||||||
|
2054 Posts Member #: 452 Post Whore Chester, UK |
14th May, 2014 at 01:12:31pm
are you using the latest version of the software? |
||||||
|
330 Posts Member #: 9628 Senior Member |
14th May, 2014 at 01:25:47pm
On 14th May, 2014 t@z said:
are you using the latest version of the software? um i downloaded it last night yeah 1.6 is the one i have can you load a map offline? also i have some mj maps but i cant load them up, when i tried too it wouldnt read them was looking for file types *nodiz :/ Edited by coopdog on 14th May, 2014. |
||||||
|
2054 Posts Member #: 452 Post Whore Chester, UK |
14th May, 2014 at 01:30:06pm
ok, did you download the latest with to your serial number?
|
||||||
|
330 Posts Member #: 9628 Senior Member |
14th May, 2014 at 02:42:11pm
ok, i need to find out what the serial number is and check that.
|
||||||
| Home > Help Needed / General Tech Chat > NoDIZ map?? | |||||||
|
|||||||
| Page: |