| Page: |
| Home > Help Needed / General Tech Chat > cam timing with a belt drive | |||||||
 1497 Posts Member #: 100 Parisien Turbo Expert Paris\' suburb |
16th Jul, 2004 at 09:34:04am
will check,
|
||||||
 1451 Posts Member #: 328 Post Whore Seaford Rise, South Australia |
16th Jul, 2004 at 12:17:38pm
On 16/07/2004 09:34:04 fab said:
will check, but pretty sure that A+ std cams, ie turbo one too are full lifted at 106? Timing a cam in using a degree figure is not as accurate as using a DTI which was Alex's original question. With a DTI you can get it spot on but with a timing disc you run the risk of being out by a couple of degrees as the engine rocks. On 5th Sep, 2011 Vegard said:
I stand corrected. You should know  |
||||||
|
1497 Posts Member #: 100 Parisien Turbo Expert Paris\' suburb |
17th Jul, 2004 at 10:50:32am
?? |
||||||
|
Site Admin  8506 Posts Member #: 16 Sold the turbo and seeing what the C20XE can do! Near Lincoln |
19th Jul, 2004 at 11:03:50am
you need a timing disc and a dti.... hence needing to be able to put full cam lift at the correct degree setting from tdc... |
||||||
|
Forum Mod 10980 Posts Member #: 17 ***16*** SouthPark, Colorado |
19th Jul, 2004 at 12:36:06pm
unless he's talking about the 'lift on overlap' technique...
On 17th Nov, 2014 Tom Fenton said:
Sorry to say My Herpes are no better Ready to feel Ancient ??? This is 26 years old as of 2022 https://youtu.be/YQQokcoOzeY |
||||||
|
1451 Posts Member #: 328 Post Whore Seaford Rise, South Australia |
19th Jul, 2004 at 02:02:25pm
On 19/07/2004 11:03:50 iain said:
you need a timing disc and a dti.... hence needing to be able to put full cam lift at the correct degree setting from tdc... No you don't just a figure for lift at tdc!!!! On 5th Sep, 2011 Vegard said:
I stand corrected. You should know |
||||||
|
Site Admin 8506 Posts Member #: 16 Sold the turbo and seeing what the C20XE can do! Near Lincoln |
19th Jul, 2004 at 03:04:39pm
my mistake |
||||||
|
Forum Mod 10980 Posts Member #: 17 ***16*** SouthPark, Colorado |
19th Jul, 2004 at 03:39:05pm
I don't know!
On 17th Nov, 2014 Tom Fenton said:
Sorry to say My Herpes are no better Ready to feel Ancient ??? This is 26 years old as of 2022 https://youtu.be/YQQokcoOzeY |
||||||
|
1451 Posts Member #: 328 Post Whore Seaford Rise, South Australia |
19th Jul, 2004 at 04:36:31pm
On 19/07/2004 15:39:05 TurboDave said:
I don't know! Or i think i don't... Good to keep you guessing! Lets just say I wasn't a million miles away from you. Edited by Scruffy on 19th Jul, 2004. On 5th Sep, 2011 Vegard said:
I stand corrected. You should know |
||||||
|
Forum Mod 10980 Posts Member #: 17 ***16*** SouthPark, Colorado |
19th Jul, 2004 at 05:05:20pm
figured it out...
On 17th Nov, 2014 Tom Fenton said:
Sorry to say My Herpes are no better Ready to feel Ancient ??? This is 26 years old as of 2022 https://youtu.be/YQQokcoOzeY |
||||||
| Home > Help Needed / General Tech Chat > cam timing with a belt drive | |||||||
|
|||||||
learning as i go and more than willing to be shown and take note.
| Page: |