| Page: |
| Home > Help Needed / General Tech Chat > no reverse | |||||||
 109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 05:26:23pm
ive just started the car again and it looks like 1st and 3rd are the same gear and 2nd,4th and reverse are all the same |
||||||
|
109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 05:27:24pm
ive just satrted the car again and it looks like 1st and 3rd are the same gear and 2nd, 4th and reverse are the same |
||||||
 6729 Posts Member #: 618 Post Whore Glasgow |
20th Oct, 2010 at 05:33:31pm
when you had the engine out, did you take the diff output covers off at all? |
||||||
|
109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 05:48:38pm
no didnt touch the engine at all |
||||||
 (2)[/url] by [url=https://www.flickr.com/photos/150672766@N03/]Rod Sugden[/url], on Fli) 5988 Posts Member #: 2024 Formally Retired Rural Suffolk |
20th Oct, 2010 at 05:58:51pm
On 20th Oct, 2010 smudger483 said:
ive just satrted the car again and it looks like 1st and 3rd are the same gear and 2nd, 4th and reverse are the same In which case the selector rod isn't rotating the internal selector through the three gates, it's just floating at the 3/4 gate. Get underneath - engine NOT running - and have someone else select the gears and see if the bottom rod is actually rotating (as well as moving backwards and forwards) and then see if the short bit of the shaft going into the gearbox also rotates at the same time (possible damaged roll pin ???) Schrödinger's cat - so which one am I ??? |
||||||
|
109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 06:03:09pm
yeh rod just done that and its just moving in and out and not rotating so do i need to just replace the roll pin |
||||||
|
5988 Posts Member #: 2024 Formally Retired Rural Suffolk |
20th Oct, 2010 at 06:19:48pm
Depends which bit is not rotating.....
Schrödinger's cat - so which one am I ??? |
||||||
 16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
20th Oct, 2010 at 06:28:59pm
On 20th Oct, 2010 smudger483 said:
no didnt touch the engine at all Cool. I've never seen anybody fit an engine using levitation. On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it 
|
||||||
|
109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 06:37:13pm
the long rod is not moving so it must be my selector box then so when i take the bottom plate off what am i looking for Edited by smudger483 on 20th Oct, 2010. |
||||||
|
5988 Posts Member #: 2024 Formally Retired Rural Suffolk |
20th Oct, 2010 at 06:43:56pm
Is the long rod rotating as well as moving ????????
Schrödinger's cat - so which one am I ??? |
||||||
|
109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 06:45:22pm
ok rod cheers ill have a quick look now |
||||||
|
109 Posts Member #: 8630 Advanced Member |
20th Oct, 2010 at 07:15:13pm
i think i need to rotate the arm 180 like tom said earlier
|
||||||
|
5988 Posts Member #: 2024 Formally Retired Rural Suffolk |
20th Oct, 2010 at 07:42:00pm
On 20th Oct, 2010 Rod S said:
It may be still assembled wrong as Tom said but there is also a roll pin inside it. On 20th Oct, 2010 Rod S said:
If the long one doesn't rotate when the stick is moved side to side, take the bottom plate off and look - believe me, it will then be obvious how it works. On 20th Oct, 2010 smudger483 said:
i think i need to rotate the arm 180 like tom said earlier I think that's all a "yes" from the photo :) Schrödinger's cat - so which one am I ??? |
||||||
| Home > Help Needed / General Tech Chat > no reverse | |||||||
|
|||||||
| Page: |