Anyone used this RR?
Turbo Mini Forums

Its a company based in Uxbridge called torque of the devil, Ive heard they know there stuff, but this was not from a mini owner!

Apparently the guy that owns it used to work from minispeed called Chris (I think)?

Anyone have any good/bad experiences with them?

EDIT: sorry forgot the link

http://www.torqueofthedevil.com/default.asp

Edited by matty on 18th Jun, 2007.

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

I think Mr Todd used to work for Power Engineering? - runs a turbo/supercharged rear engined fiesta - clever chap with a good mapping reputation - good dyno and facilities - give em a go!
JK

If Carling made Mini engines
it would probably be like this one!

Yeah sounds like the chap, my mate was telling me about his 12 second Feista, supercharged, turbo'd and nitrous...Lol...sounds like he could be worth chating to. :)

Any idea if he's good with MJ, I know he knows his way round emerald, but alot of people aren't familier with MJ.

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

He's only just set up but I have heard only positive comments.

alex

AlexF

keep us all posted gents

What are these prices like, im not to sure what the going rate is?

I know V-max seems a lot cheaper than this though!


Diagnostic - £120 exc VAT with a £50 deposit

Power test - £50 exc VAT with a £25 deposit

RR rental - (i.e. for mapping) is £90 per hour exc VAT with £40 deposit for each hour booked

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

i pay about £40ish an hour i reckon. sure thats what he said but i havent had the bill yet

Yeah £40 an hour is what Ive been charged at Vmax before.

Where did you go to get your set-up Iain?

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

Mike Barratt in Lincoln.

He's a bit busy at the mo, hoping to get in before avon!!!

I think I'll try Vmax again, save that RR for the other engine. LOl

Im cutting it close too, trying to get a RR sesh in the next 2 weeks hopefully!

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

keep away on mon 9th-im there (cutting it fine this year)

Hoping to get in on the 29th...fingers crossed!

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

bear in mind the slight difference in setup...

Vmax's is old and limited TOTD is very new kit :)

Alex

AlexF

it may be new kit, but im sure stuart knows what hes doing

WWW.TURBO-MINI.COM

totaly agree you can have all the fancy bits you like but if the bloke doesnt no what he is doing then a totaly waist of time.

io pay £40 an hour at t and m at colchester along with mini williams and t3tone.

always looking for them bigger bunches of bannanas

Haha, Ive got it booked for the 29th! :)

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

just booked me kean and anton in on the 30th at an RR by us for a power run each so we've got a rough idea of what we're putting out. best pull me finger out and get me oil leak fixed and wind the boost up some more.