Page:
Home > General Chat > cam follower dimensions

Joe C

User Avatar

12307 Posts
Member #: 565
Carlos Fandango

Burnham-on-Crouch, Essex

4th Sep, 2007 at 09:48:42pm

If someone has some cam followers handy could they measure them please?:)

diameter and length, and if possible thickness between the cam face and pushrod face.

On 28th Aug, 2011 Kean said:
At the risk of being sigged...

Joe, do you have a photo of your tool?



http://www.turbominis.co.uk/forums/index.p...9064&lastpost=1

https://joe1977.imgbb.com/



matty

User Avatar

8297 Posts
Member #: 408
Turbo Love Palace Fool

Aylesbury

6th Sep, 2007 at 01:45:44pm

20.60mm Dia
38.17mm Length
5.47mm Thickness

BUT there is a little kind of dimple in the centre and im pretty certain the pushrod wouldn't touch this part so the thickness between the cam face and push rod could be slightly larger?

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

iain
Site Admin

User Avatar

8506 Posts
Member #: 16
Sold the turbo and seeing what the C20XE can do!

Near Lincoln

6th Sep, 2007 at 01:47:27pm

what are those measurements for matty?

a mini? wrong units i reckon... *happy*

matty

User Avatar

8297 Posts
Member #: 408
Turbo Love Palace Fool

Aylesbury

6th Sep, 2007 at 01:56:31pm

0.81 Inch
1.50 Inch
0.18 Inch

Any better? *tongue*

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

Tom Fenton
Site Admin

User Avatar

15300 Posts
Member #: 337
Fearless Tom Fenton, Avon Park 2007 & 2008 class D winner

&

TM legend.

Rotherham South Yorkshire

6th Sep, 2007 at 01:59:42pm

13/16" diameter I have in my head somewhere?


On 29th Nov, 2016 madmk1 said:

On 28th Nov, 2016 Rob Gavin said:
 I refuse to pay for anything else


Like fuel 😂😂

Joe C

User Avatar

12307 Posts
Member #: 565
Carlos Fandango

Burnham-on-Crouch, Essex

6th Sep, 2007 at 01:59:44pm

*happy*

Cheers Matty!

On 28th Aug, 2011 Kean said:
At the risk of being sigged...

Joe, do you have a photo of your tool?



http://www.turbominis.co.uk/forums/index.p...9064&lastpost=1

https://joe1977.imgbb.com/



matty

User Avatar

8297 Posts
Member #: 408
Turbo Love Palace Fool

Aylesbury

6th Sep, 2007 at 02:07:11pm

0.81 In = 13/16 spot on Tom!

Not sure on the others as fractions though?

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

Tom Fenton
Site Admin

User Avatar

15300 Posts
Member #: 337
Fearless Tom Fenton, Avon Park 2007 & 2008 class D winner

&

TM legend.

Rotherham South Yorkshire

6th Sep, 2007 at 02:11:17pm

ER 1.5 inches = 1 1/2" !!!!!!!!!!!!!!!!!!

HA HA HA!

The 0.18" is probably 3/16" near enough, I'd imagine when they have cast the followers they are then machined to clean up and give the cup in the bottom.


On 29th Nov, 2016 madmk1 said:

On 28th Nov, 2016 Rob Gavin said:
 I refuse to pay for anything else


Like fuel 😂😂

matty

User Avatar

8297 Posts
Member #: 408
Turbo Love Palace Fool

Aylesbury

6th Sep, 2007 at 02:19:58pm

Lol thats obvious *laughing* *laughing* I was refering to the last dimension.. lol

I was thinking 3/16 for the other, its close!

https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel

www.fusionfabs.co.uk



1/4mile in 13.2sec @ 111 terminal on 15psi

graemec

940 Posts
Member #: 1424
Post Whore

Carnforth, Lancs

6th Sep, 2007 at 02:43:17pm

Presumably the radius on the end is also machined on?

Jordan

User Avatar

1913 Posts
Member #: 1392
Pointless Post Whore

Liverpool, North west

6th Sep, 2007 at 09:32:40pm

Radius?

Back once again like a renegade master
Home > General Chat > cam follower dimensions
Users viewing this thread: none. (+ 1 Guests)  
To post messages you must be logged in!
Username: Password:
Page: