| Page: |
| Home > Help Needed / General Tech Chat > Rollcage and spreader plates help please | |||||||
|
4018 Posts Member #: 1757 Back to Fucking Tool status Swindon |
6th Jan, 2008 at 05:18:00pm
i am currently looking for a rollcage for my turbo project i have found a good value full kit from roll centre which is Fia national spec has anyone used roll centre before? are they good?
Drives
|
||||||
|
4314 Posts Member #: 700 Formerly British Open Classic The West Country |
6th Jan, 2008 at 05:23:11pm
I've got one but it's not fitted yet.
Isambard Kingdom Brunel said:
Nothing is impossible if you are an Engineer |
||||||
 568 Posts Member #: 1200 Post Whore Bristol |
6th Jan, 2008 at 05:26:58pm
there is an article in minimag this month about fitting a rollcentre cage, i would assume the plates are 120mm square, they are good and being FIA approved means they are spot on, ive got a safety devices cage in my clubman but made up my own plates |
||||||
 9258 Posts Member #: 123 Post Whore Betwix Harrogate and York |
6th Jan, 2008 at 06:33:50pm
120cm square. Fastest 998 mini in the world? 13.05 1/4 mile 106mph
On 2nd Jan, 2013 fastcarl said:
the design shows a distinct lack of imagination, talk about starting off with a clean sheet of paper, then not bothering to fucking draw on it,lol On 20th Apr, 2012 Paul S said:
I'm mainly concerned about swirl in the runners caused by the tangential entry. |
||||||
 2370 Posts Member #: 719 Post Whore Horndean - Near Portsmouth |
6th Jan, 2008 at 06:51:00pm
On 6th of Jan, 2008 at 05:18pm Snakeii said:
also are the spreader pleates 120cm sq or 120mmsq... i have seen both posted arround on tm please help... paul. 120cm sqaure sounds like it could be big enough to be the floorpan!? Surely its 120mm sqaure.... |
||||||
|
4314 Posts Member #: 700 Formerly British Open Classic The West Country |
6th Jan, 2008 at 07:07:58pm
On 6th of Jan, 2008 at 06:51pm Rich1275 said:
On 6th of Jan, 2008 at 05:18pm Snakeii said:
also are the spreader pleates 120cm sq or 120mmsq... i have seen both posted arround on tm please help... paul. 120cm sqaure sounds like it could be big enough to be the floorpan!? Surely its 120mm sqaure.... 120cm square is only 11cm x 11cm not 120cm x 120cm Isambard Kingdom Brunel said:
Nothing is impossible if you are an Engineer |
||||||
 966 Posts Member #: 358 Post Whore Snetterton, Norfolk |
6th Jan, 2008 at 08:05:41pm
Rollcentre's stuff is normally very good and of a high quality. Saw them out with their pescarolo lmp car the other week and its all very impressive stuff. They have a very good reputation to uphold and i wouldn't expect any rubbish from them. |
||||||
 3329 Posts Member #: 184 Senior Member Melton Mowbray, Pie Country |
6th Jan, 2008 at 09:06:41pm
I have a rollcentre cage that I have just fitted. It came with the spreader plates as part of the kit.
http://www.twin-turbo.co.uk
|
||||||
|
4018 Posts Member #: 1757 Back to Fucking Tool status Swindon |
6th Jan, 2008 at 11:24:19pm
nice and thankyou for the enlightenment about the spreader plates tbh if i had thought about it a a bit more sencably i would have worked out 11x11 :$ cheers guys ill be looking into ordering it in the next few days i just need to make sure on the cost of delivery £20 sounds very nice but is that just for say door bars lol :) Drives
|
||||||
| Home > Help Needed / General Tech Chat > Rollcage and spreader plates help please | |||||||
|
|||||||
| Page: |