| Page: |
| Home > Help Needed / General Tech Chat > Final Drive Pinion Nut | |||||||
|
86 Posts Member #: 1240 Advanced Member Worcester |
4th Apr, 2008 at 08:32:31pm
How do people get this tightened upto the required torque setting? When I try the gearbox rocks about all over the place. |
||||||
 3756 Posts Member #: 1709 I like granny porn. LONDONSHIRE |
4th Apr, 2008 at 08:42:46pm
i lowered my car wheel (not all the weight) onto the box to keep it still On 2nd Oct, 2009 Vegard said:
On 1st Oct, 2009 Jimster said:
I bet my first wank came quicker than your first mini turbo These new modern turbos with their quick spool up time, would make the competition harder. On 15th Aug, 2011 robert said:
phew!!! thank you brett for smashing in my back doors .( not something i imagined writing... EVER) |
||||||
 6274 Posts Member #: 509 Post Whore Isle of Man |
4th Apr, 2008 at 09:26:01pm
"Turbo's make torque, and torque makes fun"
|
||||||
|
3756 Posts Member #: 1709 I like granny porn. LONDONSHIRE |
4th Apr, 2008 at 09:56:50pm
just not using a volvo..... On 2nd Oct, 2009 Vegard said:
On 1st Oct, 2009 Jimster said:
I bet my first wank came quicker than your first mini turbo These new modern turbos with their quick spool up time, would make the competition harder. On 15th Aug, 2011 robert said:
phew!!! thank you brett for smashing in my back doors .( not something i imagined writing... EVER) |
||||||
 11046 Posts Member #: 965 Post Whore Preston On The Brook |
4th Apr, 2008 at 10:02:55pm
I installed two anchor bolts into the garage floor and bolt the box to them. Carefull which way round you bolt the box when tightening and loosening On 26th Oct, 2004 TurboDave16v said:
Is it A-Series only? I think it should be... So when some joey comes on here about how his 16v turbo vauxhall is great compared to ours, he can be given the 'bird'... On 26th Oct, 2004 Tom Fenton said:
Yep I agree with TD........ |
||||||
 1451 Posts Member #: 328 Post Whore Seaford Rise, South Australia |
5th Apr, 2008 at 09:31:55am
Use a couple of g clamps to workbench or even workmate as you can stand on it as you tighten it! On 5th Sep, 2011 Vegard said:
I stand corrected. You should know  |
||||||
|
4309 Posts Member #: 1321 Post Whore Wiltshire |
5th Apr, 2008 at 09:36:10am
be careful if you anchor it to a bench...
On 7th Oct, 2010 5haneJ said:
yeah I gave it all a good prodding |
||||||
|
1425 Posts Member #: 690 Post Whore Norfolk |
5th Apr, 2008 at 09:43:09am
I used to use the sill of a car - but the 4 post is much easier to raise/lower!
If Carling made Mini engines
|
||||||
 7765 Posts Member #: 74 I pick holes in everything.. Chief ancient post excavator |
5th Apr, 2008 at 10:15:31am
I use my dad! Any better? On 13th Jul, 2012 Ben H said:
Mine gets in the way a bit, but only when it is up. If it is down it does not cause a problem. |
||||||
|
11046 Posts Member #: 965 Post Whore Preston On The Brook |
5th Apr, 2008 at 12:35:01pm
I found the wife to be too ikle On 26th Oct, 2004 TurboDave16v said:
Is it A-Series only? I think it should be... So when some joey comes on here about how his 16v turbo vauxhall is great compared to ours, he can be given the 'bird'... On 26th Oct, 2004 Tom Fenton said:
Yep I agree with TD........ |
||||||
 9327 Posts Member #: 59 First mini turbo to get in the 12's & site perv Herefordshire |
5th Apr, 2008 at 04:42:12pm
i stand on the casing, and then use my big torque wrench
|
||||||
 1128 Posts Member #: 142 Post Whore Winchester |
5th Apr, 2008 at 06:00:38pm
to get the 1st motion shaft nut off/torque it up i had to put the gearbox under the car, i used my new impact wrench to get the pinion nut off though.... no worries!
|
||||||
| Home > Help Needed / General Tech Chat > Final Drive Pinion Nut | |||||||
|
|||||||
| Page: |