| Page: |
| Home > Beginners Tech > Fitting a weber 45 | |||||||
|
10 Posts Member #: 6027 Member torpoint, cornwall |
21st May, 2009 at 08:28:12pm
I want to fit a weber to a stage 3 engine that i just brought! Upon looking through the boxes of bits that came with the engine i found a spec sheet that the previous owner had typed up.
IF SPARKS DONT FLY IT'S TOO HIGH |
||||||
|
559 Posts Member #: 2775 Post Whore Aberdeen |
21st May, 2009 at 10:11:52pm
You dont need a return and you will need a manifold for the weber. Whens the turbo or supercharger getting fitted then? |
||||||
|
Forum Mod  5933 Posts Member #: 784 9 times Avon Park Class C winner Milton Keynes |
21st May, 2009 at 10:12:33pm
You dont need a return, just the list that you already have
I seriously doubt it! |
||||||
 7765 Posts Member #: 74 I pick holes in everything.. Chief ancient post excavator |
21st May, 2009 at 10:19:03pm
On 21st May, 2009 stewart1 said:
I want to fit a weber to a stage 3 engine that i just brought! I guess you brought it home then..?? On 13th Jul, 2012 Ben H said:
Mine gets in the way a bit, but only when it is up. If it is down it does not cause a problem. |
||||||
|
559 Posts Member #: 2775 Post Whore Aberdeen |
21st May, 2009 at 10:21:12pm
I wandered how long it would take!
On 21st May, 2009 Vegard said:
I guess you brought it home then..?? |
||||||
 4630 Posts Member #: 20 My sister is so fit I won't show anyone her picture Lake District |
21st May, 2009 at 10:59:03pm
On 21st May, 2009 lockfast said:
I wandered how long it would take! Where did you wander to ? Lol. |
||||||
|
559 Posts Member #: 2775 Post Whore Aberdeen |
21st May, 2009 at 11:05:08pm
I wandered back from the pub! Can you tell? |
||||||
|
7765 Posts Member #: 74 I pick holes in everything.. Chief ancient post excavator |
22nd May, 2009 at 08:38:24am
He wandered when he brought it home?? On 13th Jul, 2012 Ben H said:
Mine gets in the way a bit, but only when it is up. If it is down it does not cause a problem. |
||||||
|
2395 Posts Member #: 229 Gavin@minispares.com kent |
22nd May, 2009 at 09:15:39am
Misab plates, studs and nuts? |
||||||
|
10 Posts Member #: 6027 Member torpoint, cornwall |
22nd May, 2009 at 08:02:25pm
Iv also got a metro turbo HIF44 and got my weber today! I'm going to see paul inch (think he races mighty mini's) tomorrow to see if there is any way that i can run a turbo through the weber!
IF SPARKS DONT FLY IT'S TOO HIGH |
||||||
|
7765 Posts Member #: 74 I pick holes in everything.. Chief ancient post excavator |
22nd May, 2009 at 11:24:21pm
If you'd done some searching you'd know that the 45SCOEs aren't suitable for this. On 13th Jul, 2012 Ben H said:
Mine gets in the way a bit, but only when it is up. If it is down it does not cause a problem. |
||||||
 6749 Posts Member #: 828 Post Whore uranus |
23rd May, 2009 at 05:48:38am
dcoe? Medusa + injection = too much torque for the dyno ..https://youtu.be/qg5o0_tJxYM |
||||||
|
10 Posts Member #: 6027 Member torpoint, cornwall |
23rd May, 2009 at 11:46:22am
Im only asking as i have the two units to choose from and i was interested to know whether it could have been done! IF SPARKS DONT FLY IT'S TOO HIGH |
||||||
|
559 Posts Member #: 2775 Post Whore Aberdeen |
23rd May, 2009 at 11:52:21am
You could have typed in the question to the search box just as quick? Then if you didnt understand something you could hvae asked? It saves a lot of the same questions comming up again and again and you would get alot more info and knowledge doing it that way. |
||||||
 6274 Posts Member #: 509 Post Whore Isle of Man |
25th May, 2009 at 11:03:06am
youll also need to weld in a bulkhead box to fit the 5" fanimold "Turbo's make torque, and torque makes fun"
|
||||||
| Home > Beginners Tech > Fitting a weber 45 | |||||||
|
|||||||
| Page: |