| Page: |
| Home > Help Needed / General Tech Chat > main bearing from mini spares, on side cant be fitted. | |||||||
|
83 Posts Member #: 6003 Advanced Member |
14th Nov, 2009 at 06:54:46pm
i bought the main bearings from spares. and i find all the shells are same, and they same as the original shells engine block side,there is hole on each shell ,and groove isnt at midder.
|
||||||
 16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
14th Nov, 2009 at 07:38:07pm
ring minispares back if you think you have the wrong bearings On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it 
|
||||||
 6274 Posts Member #: 509 Post Whore Isle of Man |
14th Nov, 2009 at 07:52:58pm
i fell for this one recently
"Turbo's make torque, and torque makes fun"
|
||||||
|
83 Posts Member #: 6003 Advanced Member |
14th Nov, 2009 at 08:05:20pm
On 14th Nov, 2009 joeybaby83 said:
i fell for this one recently this is the difference between A and A+ bearings You have an A set, and need to order an A+ set by the sounds of it ohh, just find all of the main bearings in mini spares are A 
|
||||||
 9258 Posts Member #: 123 Post Whore Betwix Harrogate and York |
14th Nov, 2009 at 08:31:03pm
Exactly the same happend to me only last week.
Fastest 998 mini in the world? 13.05 1/4 mile 106mph
On 2nd Jan, 2013 fastcarl said:
the design shows a distinct lack of imagination, talk about starting off with a clean sheet of paper, then not bothering to fucking draw on it,lol On 20th Apr, 2012 Paul S said:
I'm mainly concerned about swirl in the runners caused by the tangential entry. |
||||||
|
83 Posts Member #: 6003 Advanced Member |
14th Nov, 2009 at 08:34:18pm
On 14th Nov, 2009 wil_h said:
Exactly the same happend to me only last week. As stated you need A+ no A bearings. unlucky....so will did you get the a+ one..is mini sport any good? |
||||||
|
9258 Posts Member #: 123 Post Whore Betwix Harrogate and York |
14th Nov, 2009 at 09:48:22pm
I'd had the wrong bearings in my garage for 2 years, I only discovered they were wrong when I opend the pack, can't even remember where I bought them.
Fastest 998 mini in the world? 13.05 1/4 mile 106mph
On 2nd Jan, 2013 fastcarl said:
the design shows a distinct lack of imagination, talk about starting off with a clean sheet of paper, then not bothering to fucking draw on it,lol On 20th Apr, 2012 Paul S said:
I'm mainly concerned about swirl in the runners caused by the tangential entry. |
||||||
|
458 Posts Member #: 1840 Senior Member Kings Lynn, Norfolk |
14th Nov, 2009 at 10:03:18pm
LMAO i have a set of 998 and 1275 bearings both with the same problems as i wasn't capeable of reading the confusing descriptions properly. |
||||||
 7265 Posts Member #: 1268 The Boom Boom speaker Police! Essex |
14th Nov, 2009 at 10:24:13pm
This got me too. lol In the 13's at last!.. Just |
||||||
|
83 Posts Member #: 6003 Advanced Member |
15th Nov, 2009 at 08:32:12am
ok i have orded from plmini
|
||||||
 9812 Posts Member #: 332 Resident Cylinder Head Modifier Mitsi Evo 7, 911, Cossie. & all the chavs ...... won no problem |
15th Nov, 2009 at 11:45:07am
On 14th Nov, 2009 joeybaby83 said:
i fell for this one recently this is the difference between A and A+ bearings You have an A set, and need to order an A+ set by the sounds of it Thats it !
|
||||||
|
2395 Posts Member #: 229 Gavin@minispares.com kent |
16th Nov, 2009 at 01:27:20pm
Funnily enough i updated a few of these descriptions a couple of weeks ago, hope they make sense now :) |
||||||
|
9258 Posts Member #: 123 Post Whore Betwix Harrogate and York |
16th Nov, 2009 at 01:58:44pm
Good. As it seems to happen a lot (and even to some who are not exactly new to A-series tuning) there is obviously a need to highlight the differance. Fastest 998 mini in the world? 13.05 1/4 mile 106mph
On 2nd Jan, 2013 fastcarl said:
the design shows a distinct lack of imagination, talk about starting off with a clean sheet of paper, then not bothering to fucking draw on it,lol On 20th Apr, 2012 Paul S said:
I'm mainly concerned about swirl in the runners caused by the tangential entry. |
||||||
| Home > Help Needed / General Tech Chat > main bearing from mini spares, on side cant be fitted. | |||||||
|
|||||||
| Page: |