| Page: |
| Home > Help Needed / General Tech Chat > inner sill | |||||||
 76 Posts Member #: 2043 Advanced Member |
5th Dec, 2009 at 04:58:39pm
hi all, going to start replacing my drivers side floor pan and inner sill next week jus wondering if i cut both out do i need to brace it up beforehand?
Edited by timboc on 6th Dec, 2009. |
||||||
 9812 Posts Member #: 332 Resident Cylinder Head Modifier Mitsi Evo 7, 911, Cossie. & all the chavs ...... won no problem |
6th Dec, 2009 at 10:18:07am
in short No! as long as you leave the outer sill on
|
||||||
|
76 Posts Member #: 2043 Advanced Member |
6th Dec, 2009 at 10:25:36am
bummer, outer sill is off, a-panel is off and front is off, |
||||||
 9502 Posts Member #: 1023 Post Whore Doncaster, South Yorkshire |
6th Dec, 2009 at 10:45:31am
On 6th Dec, 2009 timboc said:
bummer, outer sill is off, a-panel is off and front is off, then i would 
Yes i moved to the darkside |
||||||
 (2)[/url] by [url=https://www.flickr.com/photos/150672766@N03/]Rod Sugden[/url], on Fli) 5988 Posts Member #: 2024 Formally Retired Rural Suffolk |
6th Dec, 2009 at 11:09:06am
If the door tread section is still there and 100% sound you may be OK but even if it is, personally I would tack a brace just above it across the openning just to be on the safe side. The door tread alone isn't that strong. Schrödinger's cat - so which one am I ??? |
||||||
 16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
6th Dec, 2009 at 11:22:12am
I think this is one of those questions that if you have to ask, then you already know the answer On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it 
|
||||||
 1451 Posts Member #: 328 Post Whore Seaford Rise, South Australia |
6th Dec, 2009 at 11:25:44am
Is this an outer seal?
On 5th Sep, 2011 Vegard said:
I stand corrected. You should know  |
||||||
|
76 Posts Member #: 2043 Advanced Member |
6th Dec, 2009 at 05:02:07pm
so whats the best way to brace it up? |
||||||
|
16540 Posts Member #: 4241 King Gaycharger, butt plug dealer, Sheldon Cooper and a BAC but generally a niceish fella if you dont mind a northerner Rotherham, South Yorkshire |
6th Dec, 2009 at 05:25:35pm
weld some box section to the seam where the rubber door seal attaches. About 6" above where you are working so that you have room to get your tools near your work. On 11th Feb, 2015 robert said:
i tried putting soap on it , and heating it to brown , then slathered my new lube on it
|
||||||
|
5988 Posts Member #: 2024 Formally Retired Rural Suffolk |
6th Dec, 2009 at 05:32:57pm
Or angle iron like in the picture below the seal...... Schrödinger's cat - so which one am I ??? |
||||||
| Home > Help Needed / General Tech Chat > inner sill | |||||||
|
|||||||
| Page: |