| Page: |
| Home > Help Needed / General Tech Chat > No boost | |||||||
 825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
3rd Mar, 2012 at 09:07:59pm
Don’t think there is enough preload is there, but would that not give no boost at all ?..
Main Build
|
||||||
|
825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
3rd Mar, 2012 at 09:10:25pm
Don’t think there is enough preload is there, but would that not give no boost at all ?..
Main Build
|
||||||
|
825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
3rd Mar, 2012 at 09:12:45pm
Sorry guys double post.. Main Build
|
||||||
 3673 Posts Member #: 9300 Post Whore Quarry Bonk |
3rd Mar, 2012 at 09:18:07pm
That'd probably push the wastegate open a little bit under the slight pressure on the wastegate from the turbo, and the exhaust gasses. Wind it in another 3/4mm and see if you notice any difference. On 26th Jan, 2012 Tom Fenton said:
ring problems are down to wear or abuse but although annoying it isn't a show stopper On 5th Aug, 2014 madmk1 said:
Shit the bed! I had snapped the end of my shaft off!! 17.213 @ 71mph, 64bhp n/a (Old Engine) |
||||||
|
825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
3rd Mar, 2012 at 09:27:44pm
Will do when I put It all back together, do you know what kind of seal is needed between these two mating surfaces, when I striped it down first time, I was able to put one half in my lath and face it up, but struggled to get other flat..
Main Build
|
||||||
 8297 Posts Member #: 408 Turbo Love Palace Fool Aylesbury |
3rd Mar, 2012 at 09:37:49pm
Yeah you need more preload, the width of the pin should be enough. Try it with more preload, if you still have no boost disconnect the pipe to the actuator and try it again. https://www.facebook.com/pages/Fusion-Fabri..._homepage_panel
|
||||||
|
1226 Posts Member #: 9271 Post Whore Stoke on Trent |
3rd Mar, 2012 at 09:42:01pm
On 3rd Mar, 2012 nala56 said:
Will do when I put It all back together, do you know what kind of seal is needed between these two mating surfaces, when I striped it down first time, I was able to put one half in my lath and face it up, but struggled to get other flat.. just found this on ebay, but im sure ive read of people using an exhaust sealing paste instead. http://www.ebay.co.uk/itm/AGP-TURBONETICS-...#ht_1262wt_1037 one day boost will be mine!
On 10th Mar, 2012 Joe C said:
TBH peple stick it everywhere... and theres merits to each... |
||||||
|
3673 Posts Member #: 9300 Post Whore Quarry Bonk |
3rd Mar, 2012 at 09:46:16pm
Not sure if there is a gasket there, if there wasnt to begin with and you fit one, the wastegate might not seal up properly when closed as that gasket looked quite thick. I'd use this if it were me http://www.gbdriver.co.uk/index.php?main_p...d43a3b340a917d0 On 26th Jan, 2012 Tom Fenton said:
ring problems are down to wear or abuse but although annoying it isn't a show stopper On 5th Aug, 2014 madmk1 said:
Shit the bed! I had snapped the end of my shaft off!! 17.213 @ 71mph, 64bhp n/a (Old Engine) |
||||||
 12307 Posts Member #: 565 Carlos Fandango Burnham-on-Crouch, Essex |
3rd Mar, 2012 at 09:54:29pm
if youve skimed that housing that bolts on the flap may contact the turbo on the piss adn not seal, iirc theree is an amount of wibble on it though so it can seal flat. On 28th Aug, 2011 Kean said:
At the risk of being sigged... Joe, do you have a photo of your tool? http://www.turbominis.co.uk/forums/index.p...9064&lastpost=1 https://joe1977.imgbb.com/ |
||||||
|
825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
3rd Mar, 2012 at 09:59:26pm
When I first striped the turbo there were no gasket at all on it, I wounded then If it should have one, looking at the post, wez as put on, would i be right thinking it should ? .. Main Build
|
||||||
|
825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
3rd Mar, 2012 at 10:02:13pm
Checked that Joe, seems to be OK..
On 3rd Mar, 2012 Joe C said:
if youve skimed that housing that bolts on the flap may contact the turbo on the piss adn not seal, iirc theree is an amount of wibble on it though so it can seal flat. Main Build
|
||||||
|
825 Posts Member #: 9661 Post Whore Sheffield South Yorkshire GB. |
7th Mar, 2012 at 10:55:08pm
Hi Guys a quick update striped down the turbo, could not find a lot wrong with it, the turbo its self was a bit tight from being stood in my sons garage for a number of years, I'm happy to report that I freed up the turbo and put more presser on the waste gate and now it spins up OK, not road tested it yet, but we can now hear the dump valve, thanks for your help guys.. Main Build
|
||||||
|
3673 Posts Member #: 9300 Post Whore Quarry Bonk |
7th Mar, 2012 at 11:38:42pm
No worries, Nice when the solution doesn't involve spending money! On 26th Jan, 2012 Tom Fenton said:
ring problems are down to wear or abuse but although annoying it isn't a show stopper On 5th Aug, 2014 madmk1 said:
Shit the bed! I had snapped the end of my shaft off!! 17.213 @ 71mph, 64bhp n/a (Old Engine) |
||||||
| Home > Help Needed / General Tech Chat > No boost | |||||||
|
|||||||
| Page: |