| Page: |
| Home > Help Needed / General Tech Chat > rollcage | |||||||
 192 Posts Member #: 837 Advanced Member rugby |
5th Jul, 2006 at 06:48:14pm
ello ello ello
|
||||||
|
Site Admin  8506 Posts Member #: 16 Sold the turbo and seeing what the C20XE can do! Near Lincoln |
5th Jul, 2006 at 06:58:38pm
spreading the loads on the floor. fairly simple to make up, think the size for FIA status is 3mm thick and 120mm square |
||||||
 2924 Posts Member #: 95 Post Whore liverpool-on-sea |
5th Jul, 2006 at 07:31:37pm
if you ring saftey devices thell sell you a fitting kit which includes all the nuts, bolts and washers and the weld in plates, be warned not cheap tho no longer a series, but still 1.3 turbo.
On 28th Nov, 2008 Sprocket said:
Oh now that is a long shaft you have Carl. |
||||||
 9258 Posts Member #: 123 Post Whore Betwix Harrogate and York |
5th Jul, 2006 at 07:32:53pm
Speak to the roll centre or safety devices as they will sell you the plates, or as above make them up.
Fastest 998 mini in the world? 13.05 1/4 mile 106mph
On 2nd Jan, 2013 fastcarl said:
the design shows a distinct lack of imagination, talk about starting off with a clean sheet of paper, then not bothering to fucking draw on it,lol On 20th Apr, 2012 Paul S said:
I'm mainly concerned about swirl in the runners caused by the tangential entry. |
||||||
|
192 Posts Member #: 837 Advanced Member rugby |
1st Aug, 2006 at 07:18:26pm
cheers guys i will try making them
|
||||||
|
192 Posts Member #: 837 Advanced Member rugby |
18th Sep, 2006 at 07:01:03pm
ello again,
|
||||||
|
Site Admin  15302 Posts Member #: 337 Fearless Tom Fenton, Avon Park 2007 & 2008 class D winner & TM legend. |
18th Sep, 2006 at 07:17:47pm
No you should not need to cut the pockets. Remove all front and rear seats. Position the rollcage rear hoop where the front seats would be, lying on its "front", with the rear stay legs up in the air. Then you need to "roll" the cage from where it is, into the upright position, hooking the feet over the rear pockets into roughly the right position. You may find you need to use a ratchet strap around the legs to pull them together slightly to get past the B pillars.
On 29th Nov, 2016 madmk1 said:
On 28th Nov, 2016 Rob Gavin said:
I refuse to pay for anything else Like fuel 😂😂 |
||||||
|
192 Posts Member #: 837 Advanced Member rugby |
21st Sep, 2006 at 07:49:06pm
cheers tom got it in |
||||||
 1840 Posts Member #: 54 Post Whore nr coventry |
21st Sep, 2006 at 09:02:54pm
sorry for the hi-jack, i have a six point cage, i think its a satety devices & wanted to know if i can get doorbars for it as mine does'nt have the mounts on the parts i have if ya get my vague meanin SKYLINES ARE LIKE CLITS, EVERY FLANGE SEEMS TO HAVE ONE: see this sticker on my silvia
|
||||||
|
2924 Posts Member #: 95 Post Whore liverpool-on-sea |
21st Sep, 2006 at 09:08:22pm
the saftey devises door bars clamp around the cage so yes you should have no probs getting them most mini suppliers stock them no longer a series, but still 1.3 turbo.
On 28th Nov, 2008 Sprocket said:
Oh now that is a long shaft you have Carl. |
||||||
 9812 Posts Member #: 332 Resident Cylinder Head Modifier Mitsi Evo 7, 911, Cossie. & all the chavs ...... won no problem |
22nd Sep, 2006 at 03:03:37am
On 05/07/2006 19:31:37 Carl said:
if you ring saftey devices thell sell you a fitting kit which includes all the nuts, bolts and washers and the weld in plates, be warned not cheap tho  your right carl but......... these plates "if not painted before fitment" (will rust!) i made mine out of 5mm satainless steel! the underside ones
|
||||||
| Home > Help Needed / General Tech Chat > rollcage | |||||||
|
|||||||
| Page: |