| Page: |
| Home > Help Needed / General Tech Chat > Idler Gear Bearing | |||||||
 1050 Posts Member #: 764 Post Whore Staffordshire |
31st May, 2007 at 10:00:57pm
How do you get the gearbox side idler gear bearing out? Do I need a special tool? |
||||||
 2924 Posts Member #: 95 Post Whore liverpool-on-sea |
31st May, 2007 at 10:07:22pm
do a search mate theres a few methods all been covered before. no longer a series, but still 1.3 turbo.
On 28th Nov, 2008 Sprocket said:
Oh now that is a long shaft you have Carl. |
||||||
|
Site Admin  15302 Posts Member #: 337 Fearless Tom Fenton, Avon Park 2007 & 2008 class D winner & TM legend. |
31st May, 2007 at 10:07:23pm
Hammer and a drift......
On 29th Nov, 2016 madmk1 said:
On 28th Nov, 2016 Rob Gavin said:
I refuse to pay for anything else Like fuel 😂😂 |
||||||
 9812 Posts Member #: 332 Resident Cylinder Head Modifier Mitsi Evo 7, 911, Cossie. & all the chavs ...... won no problem |
1st Jun, 2007 at 12:58:12am
steady!
|
||||||
|
1641 Posts Member #: 178 Post Whore stowmaket suffolk |
1st Jun, 2007 at 06:39:44am
clean well the place in oven at 200 deg for about 20 mins then it will fall out always looking for them bigger bunches of bannanas |
||||||
 2514 Posts Member #: 1217 I like nice quiet girly Minis Cheltenham, Gloucestershire |
1st Jun, 2007 at 07:12:49am
by clean he means spotless!!!
Every day is a school day ...........
On 27th of Sep, 2007 at 12:45pm Jimster said:
why do you you think I got a girlfriend with small hands? |
||||||
 4559 Posts Member #: 786 Post Whore Bermingum |
1st Jun, 2007 at 08:57:25am
Hi,
VEMs Authorised Installer / Re-seller. K head kits now available!
|
||||||
|
1303 Posts Member #: 30 Post Whore Epsom, Surrey |
1st Jun, 2007 at 09:00:58am
hammer and punch. there not that tight. |
||||||
|
9812 Posts Member #: 332 Resident Cylinder Head Modifier Mitsi Evo 7, 911, Cossie. & all the chavs ...... won no problem |
1st Jun, 2007 at 09:49:01am
i think hoggy is meaning the transfer case
|
||||||
|
1050 Posts Member #: 764 Post Whore Staffordshire |
1st Jun, 2007 at 09:52:29pm
done it... hammer and drift would not shift it... managed to find a beefy washer that was the "perfect" size to get behind it. attached a bolt and hit it... was out with a couple of taps...
|
||||||
|
1641 Posts Member #: 178 Post Whore stowmaket suffolk |
2nd Jun, 2007 at 07:25:28am
sorry yes read q wrong.
always looking for them bigger bunches of bannanas |
||||||
 982 Posts Member #: 97 Post Whore Near Daventry, midlands |
2nd Jun, 2007 at 09:24:25am
If you plain drift this bearing out it normally scores the bore the bearing sits in, its therefore far better (if you plan on re-using the case) to heat the area with a blow torch for a few mins before removing the bearing. You'll find the bearing will literally just fall out when you are at the right temp. I've seen the future and tbh its Pie
|
||||||
|
2514 Posts Member #: 1217 I like nice quiet girly Minis Cheltenham, Gloucestershire |
2nd Jun, 2007 at 12:44:26pm
I sized my oven specifically .......
Every day is a school day ...........
On 27th of Sep, 2007 at 12:45pm Jimster said:
why do you you think I got a girlfriend with small hands? |
||||||
| Home > Help Needed / General Tech Chat > Idler Gear Bearing | |||||||
|
|||||||
| Page: |